Share your SWITCH v2.0 Experience

@Proton

Thank you very much for sharing.. I still have a question on your LACP lab, didn’t you execute “no shutdown” on fa0/3-4 on both side after all the changes made?

@Proton

Are you pertaining to the below question that you have noted?

A single server in Company ABC is connected via EtherChannel to a single upstream Layer 2 switch. Which EtherChannel load balancing methods on the switch make optimal use of the redundant links as traffic flows from the router that is the default gateway to the server?

A. source MAC address
B. source IP address
C. destination MAC address
D. destination IP address

Correct answer is B

@Proton

Thanks for sharing! Have you noticed the switch models used for LACP lab?

@Proton And @Richard

Regarding the HSRP Lab, Even if the track is on the E1/0, the Answer is the same(The interface will have its current priority incremented by 40 for HSRP group 1), because the HSRP will decrement and increment using where the Track Interface Line Protocol is configured.

See the link https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipapp/configuration/xe-16/iap-xe-16-book/iap-eot.pdf

See the part “In the following example, the tracking process is configured to track the line-protocol state of GigabitEthernet
interface 1/0/0. HSRPon GigabitEthernet interface 0/0/0 then registers with the tracking processto be informed
of any changes to the line-protocol state of GigabitEthernet interface 1/0/0. If the line protocol on
GigabitEthernet interface 1/0/0 goes down, the priority of the HSRP group is reduced by 10.”

How many VLANs can be assigned to a user access port configured for VoIP?

A. 1
B. 2
C. 3
D. unlimited

I’m not sure A or B.
Answer is A. ….

Yo everyone! Can I use tap or help(?) On Labs int real exam?

@Vin – Yes I’ve shutdown both interface 0/3 and 0/4 on both switch and as soon as I finish the configuration on both ends I un shutdown those links.

That is the correct question but the answer I choose is destination address. The question includes two routers or one (can’t remember) attach to a switch and the switch is attached to a server using multiple port (multiple ports means multiple mac address per nic) so I choose destination address.

@fafacalvs – I did not perform show version on the switch but someone explained on this site that the reason you performed encapsulation dot1q on switch b because of the version.

@MED – As for the HSRP Lab, as previously mentioned you only have access to R1 and R2. From what I can remember, the interface connecting to R5 does not have any Standby configuration so in reality there’s really no answer at all (not sure if the interface was tracked or anything)

The interface of R1 connecting to R5 only have these configuration

interface e0/1
ip address 192.168.1.1/24

(can’t remember the exact IP Address) If you will look to this interface it’s clearly not participating on any HSRP Group.

For those who passed, feel free to add any information or correct me if I am wrong.

@Proton

thanks allot

i will post some other questions in addition of proton which are in real exam need to correct answers.

@Karim

hi karim nice to see to back to discussion group…as preparing exam for tomorrow ..any suggest?

Dear all,
Just passed SWITCH, The dump is still valid, Same SIMs ( VTPv3 /HSRP/ LACP with STPv3),
D&D : RSPAN and RADIUS vs TACACS+ ..
– MCQ about DHCP snooping, IP Src guard, DAI, RADIUS vs TACACS+ and AAA, Native Vlan, Transparent mode, HSRP timers – 256 groups /GBLP /VRRP tracking and authentication / SDM prefer routing / CDP enable/run ..
STP Root guard/ BPDU filter and guard / Dot1q trunking
CDP vs LLDP
Good luck for all..

Dear’s
any one please mention correct answer many question coming from this file it will be helpfull to all
i cant past answer options as its as snapshot

1.Which feature prevents a switch port from receiving and forwarding general traffic, so that it handles only a copy of specifically designated traffic?

Ans. A

2. Which device type can act as a client in a system that uses TACACS+?

Ans. C

3.A server with a statically assigned IP address is attached to a switch that is provisioned for DHCP snooping. For more protection against malicious attacks, the network team is considering enabling dynamic ARP inspection alongside DHCP snooping. Which solution ensures that the server maintains network reachability in the future?

Ans. B

4. Which two statements about HSRP times are true? (Choose two.)

Ans. B, C

5. Which two statements about VRRP object tracking are true? (Choose two.)

Ans. A, C

6.When a Layer 2 EtherChannel is configured, which statement about interaction with the Spanning Tree Protocol is true?

Ans. D

7. Which to features does TACACS+ support? (Choose two.)

Ans. A, B

8. Which two statements about IP Source Guard are true? (Choose two.)

Ans. A, C

9.

Refer to the exhibit. You have applied these configurations to Switches A, B, and D respectively, and the switches are connected to one another on a trunk port that is passing all VLAN traffic. Which statement about traffic on the network is true?

Ans. A

10. Which Cisco StackWise feature is supported?

Ans. A

11. Which HSRP identifier can an end station use to find default gateway at the data link layer?

Ans. A

12.

Refer to the exhibit. Which statement about the port channel must be true?

Ans. B

13.Which two tasks must you perform to enable DHCP option 82 on an untrusted port? (Choose two.)

Ans. B, C

14. Which two statements about UDLD aggressive mode are true? (Choose two.)

Ans. A, C

15. Which command maximizes system resources for ACLs?

Ans. A

16.

Refer to the exhibit. Which spanning-tree feature is configured on this interface?

Ans. D

17. Which two accounting types does AAA support? (Choose two.)

Ans. A, D

18.Which two pieces of information are carried in a Cisco Discovery Protocol advertisement? (Choose two.)

Ans. B, D

19.A network engineer wants to ensure Layer 2 isolation of customers traffic using a private VLAN. Which configuration must be made before the private VLAN is configured?

Ans. B

20. Which two statements about LLDP frames are true? (Choose two.)

Ans. B, C

21.Which commands configures all access ports on a switch to immediately enter the forwarding state when the switch is reset?

Ans. A

22. Which feature can protect a Layer 2 port from spoofed IP addresses?

Ans. D

23.Drag and drop the statements about remote security database from the left onto the correct security database types on the right.

24.Which STP feature can ensure that the path to the root bridge of the network remains consistent with the original network design?

Ans. D

25. To which VLAN is a dynamic access port assigned by default?

Ans. D

26. Which two statements about HSRP, GLBP, and VRRP are true? (Choose two.)

Ans. A, D

27.A network engineer deployed a switch that operates the LAN base feature set and decides to use the SDM VLAN template. The SDM template is causing the CPU of the switch to spike during peak working hours. What is the root cause of this issue?

Ans. C

28. How does the Spanning Tree Protocol determine path cost?

Ans. D

29. Which two differences between RADIUS and TACACS+ are true? (Choose two)

Ans. A, E

30. Which two commands verify the DHCP snooping configuration on a device? (Choose two.)

Ans. B, C

31. Which statement about SPAN is true?

Ans. B

32. Which two statements about VTP modes are true? (Choose two.)

Ans. A, B

33. Which HSRP extension allows groups to share traffic loads?

Ans. E

34.Which fallback method can you configure to allow all AAA authorization requests to be granted if the other methods do not respond or return an error?

Ans. A

35. Which two commands can you enter to configure load-balancing at Layer 2? (Choose two)

Ans. A, B

36. Which three features of AAA with TACACS+ are true? (Choose three)

Ans. A, B, F

37. Which feature prevent an interface from sending BGDUs on a portfast enable port?

Ans. C

38. Which statement about Cisco StackWise is true?

Ans. A

39.

40.

Refer to the exhibit. Which two statements about the network environment are true? (Choose two)

Ans. B, E

41.Refer to the output below. Which statement about the current configuration on port GigabitEthernet2/0/1 is true?

Ans. D

@Karim please could you send those snaps to my email
Mohamed-hassan92@ Hotmail. com

@ Proton

Please can you verify above questions this may include remaining questions yo missed to past above

@ Mo

please check em,ail and update me too with correct answers if you have file.

Hello friends!

Did someone see in exam MLS and EIGRP lab? Why we need this on switch exam?
thanks

@ Mo,

Please could you send me a copy of those snaps to my email. I dropped you an email.

@ BEZ

those questions answers must be verify as many question answers selection is wrong

update here

@ BEZ

did you receive it ?

@Karim

Are those questions from a recent exam? The snapshots?
Or are they just questions you would like answering?

@karim
please snap me to my email above Q please

to subnet8 AT GMAIL DOT COM

@Proton
@CCNPBound
In regards to the VTPv3 sim, question about adding vlans 500 and 600. I am confused as to the correct answer. This site says to configure 500 & 600 on both SW1 & SW2. Unless I am looking at it wrong, SW is in fact running VTPv3 and is the Primary Server. In that case I would think you would only need to add 500/600 to SW1. Do you agree or am I wrong?

I am taking my exam soon so I would appreciate knowing how to answer this question.

Thank you!

Could anybody share *.vce file pls?

Karim,

Ive found all question apart from the below…
Would you please mind writing the possible answers?
1.Which feature prevents a switch port from receiving and forwarding general traffic, so that it handles only a copy of specifically designated traffic?
A.
B.
C.
D.
Ans. A

4. Which two statements about HSRP times are true
A.
B.
C.
D.
Ans. B, C

7. Which to features does TACACS+ support? (Choose two.)
A.
B.
C.
D.
Ans. A, B

12. Refer to the exhibit. Which statement about the port channel must be true?
A.
B.
C.
D.
Ans. B

24.Which STP feature can ensure that the path to the root bridge of the network remains consistent with the original network design?
A.
B.
C.
D.
Ans. D

Also did you see my question above? Are these from recent exam?
Thanks!

@zaza
The E-mail

@ Switchy

almost all those questions are from very recent exam attempted on 13 Feb due to wrong answer selection failed
so please try to find correct answers and share.

7. Which two features does TACACS+ support? (Choose two.)
A. PAP and CHAP authentication
B. decentralizing network access management, reducing the potential impact of a security breach to a central device
C. encrypting the entire TCP packet containing TACACS+ information
D. UDP communication between the network access server and the security server
E. combining authorization and authentication to streamline AAA services
Ans A and C

TACACS+ has the following features:
* TCP packets for reliable data transport—TACACS+ uses TCP as the communication protocol between the remote client and security server.

* —Supports the AAA architecture

* Link is encrypted—The data payload of IP packets (TCP packets) is encrypted for security and is stored in encrypted form in the remote security database.

* —Supports PAP, CHAP, and MS-CHAP authentication

* —Useful for both LAN and WAN security


24.Which STP feature can ensure that the path to the root bridge of the network remains consistent with the original network design?

Answer is BPDU Gaurd…..

The BPDU guard feature is designed to allow network designers to keep the active network topology predictable. BPDU guard is used to protect the switched network from the problems that may be caused by the receipt of BPDUs on ports that should not be receiving them.

VTPv3 Sim. – the question is actually about setting STP root priority on SW1 and SW2 for respective VLANs. A lot of people confuse that the question asking where to create the VLAN.

Read the question carefully.

It is not asking how/where you create the VLANs. Its asking how/where you configure STP priority as desired. Thats why the answer is both SW1 and SW2

@Karim..

Can you please write out selections for 1,4 and 12 ?
I can then give the answers