Share your SWITCH v2.0 Experience

@dan21 IDK I need to check those.

@Dan21 (from a couple of days ago)

Which two statements about the monitored traffic in a SPAN session are true? (Choose two.)

A . You cannot configure two separate SPAN or RSPAN source sessions with separate or overlapping sets of SPAN source ports and VLANs
B . By default, all monitored packets are captured without the IEEE 802.1Q tag
C . Egress SPAN monitors packets sent by the source interface before any QoS modifcations
D . Sources can be ports or VLANs or any combination in the same session
E . By default, all monitored packets include the IEEE 802.1Q tag that they had on the source port
F . Ingress SPAN monitors packets received by the source interface before any QoS modifications

Answers B and F

E is incorrect. Why?
By default tags on the frames are not present when monitor an 802.1Q trunk.

To mirror frames including the tags you need to specify ‘encapsulation’ option on the SPAN destination (e.g. monitor session 1 destination interface gig1/0/16 encapsulation replicate)

Then you can see them. But this is NOT the default behaviour

:)

@BoxingSurfer

I believe that is D, extended VLAN is not supported by version 1 and 2 even in transparent mode

VTP version 1 and VTP version 2 do not propagate configuration information for extended-range VLANs (VLAN numbers 1006 to 4094). You must configure extended-range VLANs manually on each network device.
VTP version 3 supports extended-range VLANs (VLAN numbers 1006 to 4094). If you convert from VTP version 3 to VTP version 2, the VLANs in the range 1006 to 4094 are removed from VTP control.

https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/15-1SY/config_guide/sup2T/15_1_sy_swcg_2T/vtp.html

@WEST

Sorry you are wrong about this. Extended VLAN are configurable in VTP Mode 1 or 2 perfectly fine but you need to be in Transparent mode to do it.

i have tested this today in real hardware.

If you have evidence that its wrong then please share it.

@WEST

please read carefully.

“VTP version 1 and VTP version 2 do not propagate configuration information for extended-range VLANs..”

-> yes this is corrent. VTP v1 and v2 do not propogate extended range VLANs.

“You must configure extended-range VLANs manually on each network device…”

-> here is the answer. This statement can be read as “use transparent mode and configure them on each device”

Concur with BoxingSurfer – as the Q is written it is looking at configuration, not propagation.
Below on a 3750G

3750G(config)#vtp ver 2
VTP version is already in V2.
3750G(config)#vtp mo s
Setting device to VTP Server mode for VLANS.
3750G(config)#vl 4000
3750G(config-vlan)#ex
% Failed to create VLANs 4000
Extended VLAN(s) not allowed in current VTP mode.
%Failed to commit extended VLAN(s) changes.
3750G(config)#vtp mo tr
Setting device to VTP Transparent mode for VLANS.
3750G(config)#vl 4000
3750G(config-vlan)#ex
3750G(config)#^Z
3750G#sh vl br

VLAN Name Status Ports
—- ——————————– ——— ——————————-
.
.
.

1002 fddi-default act/unsup
1003 trcrf-default act/unsup
1004 fddinet-default act/unsup
1005 trbrf-default act/unsup
4000 VLAN4000 active

@Harry
@anyone

Can you please\tell me if you recall HSRP and VRRP DND, This is not in the premium site.

HI everyone! If i passed 300-135 last jan 14, 2020, can i take exam 300-115 as soon as possible? does it need 180 days gap?

@NeedHelp
The 180 day gap only applies to retaking the same exam. I am not aware of any gap needed between the separate exams unless you fail one then its 5 days.

For the recent exam takers, which topics did you all find more asked then others?

Passed a couple of hours ago with a 9XX. I used the premium section of this site and 300-115 – Updated 1-09-2020 from a previous post in this forum. If you can pass each of the composite test you will have no problem passing. All the information needed is on this site.

Same Labs as everyone else. LACP/HSRP/VTP

1 D&D – TACACS vs Radius

2 new questions

@Passed Today
Congrats well done! Curious on the VTPv3 sim if you followed the site or answered questions 3 and 4 differently. Another post said they did below. On the LACP lab was any other config needed like port channel and were the interface range commands allowed?
VTPv3 Sim
I answered the following:

Q3) B Configure VLAN 500 and VLAN 600 on SW1 only
Q4) A Disable VTP pruning on SW1 only

@Switch.

I answered exactly what is posted on this site. For the LACP lab, it allowed the range command and the trunk encap dot1q command only worked on one of them. Other than that I made all changes on the physical interfaces thats posted on this site.

One the new questions was about what would be considered a TACACS client.
router
phone
workstation
something else

I choose workstation, but it was probably the router.

Just passed Switch 9xx. Finished CCNA/TSHOOT/ROUTE/SWITCH in 14 days…had to re certify after letting it expire but now I’m good for 3 more years, enough time to “feel” the next test out.

I managed to get through about 1/2 of the composite quizzes in the premium section. Only saw 1-2 questions that were not in that bank of questions!

LACP-STP
HSRP
VTPv3

2 Drag and Drop that I forgot already.

Thanks Certprepare for all the help, now it’s time for a long weekend!

How many VLANs can be assigned to a user access port configured for VoIP?

A. 1
B. 2
C. 3
D. unlimited

I’m not sure A or B.

How many VLANs can be assigned to a user access port configured for VoIP?

A. 1
B. 2
C. 3
D. unlimited

The correct answer is B.

@NANA

One VLAN for voice traffic and another VLAN for data traffic , right?

@cybernet

yes that’s correct

I failed my exam. I found 80% of questions are old question.
Does anyone found like me? There are not in New Updated Questions Part 6-8.

@cybernet

What do you mean by old question? Its from the sections or old cisco switch exam 642-813?

Hi,

Did any one faced AAAdot1x Lab Sim recently in the exam?

Hello friends!

Did someone see in exam MLS and EIGRP lab? Why we need this on switch exam?
thanks

Hi Guys,

Just passed the exam with 9xx mark.

The Labs are all the same except HSRP wherein the question is asking if R1 interface Ethernet0/1 (conneting to R5) goes down. This confuses me on the exam as the interface Ethernet 0/1 does not have any standby configuration. Instead this interface only have an IP Address configured in it. What I choose is instead the default decrement value of HSRP which is 100.

DND:

TACACS / RADIUS
Span Source and Destination
ARP,Gateway,AVG and AVF
CDP and LLDP
PVST,RPVST,MST

As for the MCQ, I found at least 4 questions that I did not encounter during my review. I will compose all the question that I can remember and post it in here later.

God Bless and Goodluck to all those will take the exam.

@Proton
You mean default decrement value of 10 instead of 100

I fail exam after stdy all quesions. Wehn in lab trunk not come up on Swith B, but come up fin on Swich A?
Is normal?

Pleze reply.

@Richard

That is correct. The question pertains that what happens when Ethernet 0/1 shut and unshut (some sort of that kind of scenario) since there’s no priority indicated then the answer will be the priority will be back to 100

@CCNP

I din’t see AAAdot1x Lab Sim in the exam?
Old question its from the sections 1-5 not 6 – 8.

@proton – I think since that interface was being “tracked” in the configuration if it goes down the HSRP info on ETH0/0 will respond. Therefore I choose the same answer as in the lab, which was “the current status of the interface will add 40…….90 + 40 = 130.

This one confused me for a min as well but 100 did not make any sense to me.

@Proton

Kindly share the question you remember. Exam on monday