Share your SWITCH v2.0 Experience

@Dan21, below my email and thank you
mohammed.alosfur(at)gmail(dot)com

@Chuck
Oh i see! I’m just wondering because it won’t work in the real world to reach the vlans from the router if fa0/1 stays in access mode. Thanks as well.

passed yesterday. 8xx mark.
labs: LACP with STP, HSRP, VTP3
DnD: source and destination span, avg|avf, pvst v1,v2 and v3, tacacs and radius.
goodluck to examinees.

All, how to prevent the Native VLAN Mismatch error messages in LACP/STP Lab? Anyone please?

@LACP with STP

you may shutdown the interface fa0/3-4 during the lab and once you are done with all the configuration, turn them back on.. don’t forget to save the configuration during the exam :)

any one have valid dump updated ?
My exam in 3 days

Which two statements about the monitored traffic in a SPAN session are true? (Choose two.)

A . You cannot configure two separate SPAN or RSPAN source sessions with separate or overlapping sets of SPAN source ports and VLANs
B . By default, all monitored packets are captured without the IEEE 802.1Q tag
C . Egress SPAN monitors packets sent by the source interface before any QoS modifcations
D . Sources can be ports or VLANs or any combination in the same session
E . By default, all monitored packets include the IEEE 802.1Q tag that they had on the source port
F . Ingress SPAN monitors packets received by the source interface before any QoS modifications

Ans: CD? Share your thoughts please. Thanks.

Premium questions are about 1000 questios, you need to register to this site on the top right corner.

I think it cost 19 per month.

When you have a premium account what is wise to practice?
separate topics or composite quizzes?
I have the feeling that composite quizzes do not cover all the questions but on the other hand i also see questions in composite quizzes which are not in separate topics, please advice.

@Vin
correct answer are B and F
Check Q7 on SPAN Questions 3 section.

BR!

I passed at 02-08-2020 – 8xx

Simlets:

HSRP
VTPv3 Sim

lab configuration:

LACP with STP

The labs are the same here. A lot of question that don’t have on PDF.

Now I will try Router.

@Anonymous D

@Anonymous

The Cisco StackWise dual-active detection mechanism is most useful under which condition?
A. when the active switch experiences a MEC link failure
B. when the active switch experiences a standby failure
C. when the active switch enters an inoperable state
D. when the active switch is still operational after a virtual link failure

I believe its D.

https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9500/software/release/16-9/configuration_guide/ha/b_169_ha_9500_cg/configuring_cisco_stackwise_virtual.html#concept_sjb_byx_31b

the answer is D

Hey guys I have premium membership . But I don’t see any pdf with 1000mcq, I can see only part 6,7,8 only.
How you guys got the pdf

@OldGuy

Huh? –> and the one “choose 2” that I keep finding the hardest – where do you configure untrusted DHCP snooping in an ISP environment.

Passed two hours ago 8xx, no news. Same labs, only two or three questions that I never seen before.

@Sarasa
Which dump you studied in premium membership
Only part 6,7,8 or any extra questions too

A question about a configuration with a dot1q enabled trunk port. (Choose two)
A. Supports VLANs 1-4096
B. Does not support tagging native VLAN
C. Dot1q supports tagging 1000 VLANs including the native VLAN
D. ?
E. ?

The answer is A and C but is there a reference document for answer C? Theoretically it should be 4094 imo?

Which two statements about the monitored traffic in a SPAN session are true? (Choose two.)

A . You cannot configure two separate SPAN or RSPAN source sessions with separate or overlapping sets of SPAN source ports and VLANs
B . By default, all monitored packets are captured without the IEEE 802.1Q tag
C . Egress SPAN monitors packets sent by the source interface before any QoS modifcations
D . Sources can be ports or VLANs or any combination in the same session
E . By default, all monitored packets include the IEEE 802.1Q tag that they had on the source port
F . Ingress SPAN monitors packets received by the source interface before any QoS modifications

I am pretty sure the span port has the vlan tags of the source

could answers be E and F?

@Dan21
B and F

Richard,

you are just taking the answer from the dump. Please elaborate…

@Dan21

https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750x_3560x/software/release/12-2_55_se/configuration/guide/3750xscg/swspan.html

“The default configuration for local SPAN session ports is to send all packets untagged”

I already have the same doubt and search for the solution and found this article in cisco

So I beleive that the switch capture the capture without any tag, it doesn’t make sense capture the packet, remore the tag and send it to SPAN, that’s is “doubling” the work and resources of the switch when it can capture without the tag and send it to SPAN.

Anyone knows it in the real exam HSRP and VTP Sim it is need to configure something or the SIM is only to troubleshot?

Had VTPv3 and HSRP simulations. at least 6 questions on HSRP,vrrp, glbp (know virtual macs for each), a question on multi chassis ethernet channels, 2 or 3 on ether channel protocols, diagram showing bridge priorities, default for one (know default bridge priority).

Hi Guys,

Can someone please elaborate the exact answer for the DND for RSPAN True and False?

Currently I have this as an answer:

RSPAN True
MAC Address
STP
VTP

RSPAN False
2-1001
2-1024

Thank you

please somebody help me how I can do to download the new question of part 6,7,8 thanj you in advance

@proton I am not sure if mac adress learning is disabled. I have the same doubt with that D&D.
I think this can be the answer

RSPAN True
2-1001
STP
VTP

RSPAN False
Mac address
2-1024